Flanges are called threaded flanges as it is mounted on pipe with help of female threading on the line and male threading on the pipe line. Threaded flanges are used in lines where fast dismantling is required and threaded flanges are mainly used in low pressure in line. It can also be used at places where in welding is not possible due to exploding nature of line fluid. We are recognised as quality threaded flange manufacturer in India.
| DIMENSIONS TOLERANCES OF FLANGES (in mm) | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| Welding neck | Threaded, Slip on lap joint, Socket welding and blind |
||||||||
| * | outside diameter | O.D. 600 if smaller | + 1.6
_ |
||||||
| O.D. over 600 | + 3.1
_ |
* | outside diameter | O.D. 600 or smaller | + 1.6
_ |
||||
| O.D. over 600 | + 3.1
_ |
||||||||
| 250 and smaller | + 0.7
_ |
inside diameter | threaded : to stand gauge limit | ||||||
| inside diameter | 12 though 450 | + 1.6
_ |
(bore) | slop on .lap joint : socket-welding | |||||
| (bore) | 500 and larger | + 3.1 |
- 1.6 |
250 and smaller | + 0.7 |
- 0.0 |
|||
| 300 and larger | + 1.6 |
- 0.0 |
|||||||
| 1.6 raised face | + 0.4
_ |
threaded | |||||||
| diameter of | 6.3 raised face tounge & | diameter of | 250 and smaller | + 0.7 |
- 0.0 |
||||
| contact face | groove male and female | + 0.4
_ |
counter bore | 300 and larger | + 1.6 |
- 0.0 |
|||
| * | outside diameter | 300 and smaller | + 2.3 |
- 1.6 |
|||||
| * | diameter of hub | 125 and smaller | + 2.2 |
- 0.7 |
of hub | 350 and larger | + 3.1
_ |
||
| at point of weding | 150 and larger | + 4.0 |
- 0.7 |
||||||
| diameter of | 1.6 raised face | + 0.7
_ |
|||||||
| contact face | 6.3 raised fact tongue & grooved | ||||||||
| Thickness | 450 and smaller | + 3.1 |
- 0.0 |
male & female | + 0.4
_ |
||||
| 500 and larger | + 4.7 |
- 0.0 |
|||||||
| Thickness | 450 and smaller | + 3.1 |
- 0.0 |
||||||
| length through | 250 and smaller | + 1.6
_ |
hub | 500 and larger | + 4.7 |
- 0.0 |
|||
| hub | 300 and larger | + 3.1
_ |
|||||||
| * | length through | 450 and smaller | + 3.0 |
- 1.6 |
|||||
| hub | 500 and larger | + 4.8 |
- 1.6 |
||||||
| bolt circle | 600 and smaller | + 0.7
_ |
|||||||
| 600 and larger | + 1.6
_ |
bolt circle | + 1.6
_ |
||||||
| drilling | bolt hole spacing | + 0.7
_ |
|||||||
| drilling | bolt hole spacing | + 0.7
_ |
|||||||
| eccenticity with respect | eccenticity with respect | ||||||||
| to bore | 0.70 max | to bore | 0.70 max | ||||||
